BuddeMix Stirring System 1 - 4
CHF 438.60*
Content:
1
Delivery according to order confirmation
Product number:
9779352
Manufacturer:
Buddeberg GmbH
Packaging information:
Length:
343 mm
Width:
50 mm
Height:
45 mm
Weight:
0.248 kg
Description
This novel stirring system has been conceived to mix low viscosity fluids as well as highly viscous media at slow speeds. Its special design creates inherent dynamic currents to produce perfectly homogeneous mixing results in very little time. Additional components like baffles, bottom bearings, etc. are not needed.
Advantages at a glance:
Particularly for potentially explosive atmospheres:
Customised shaft length possible. Fine polishing Ra 0.6 to 0.8 µm and/or material certificate available on request.
Advantages at a glance:
- suitable for low to highly viscous fluids
- stirs media containing solids and fibres without any difficulty
- gentle, low-shear stirring, due to slow stirring speed
- constant product temperature, with no heating effect
- short mixing times as the entire contents of the container are agitated
- no air addition, no foaming
- no baffles required
- low gear wear due to balanced forces
- minimal power consumption thanks to low speeds and short operation times
- easy cleaning
- material no. 1.4404
Particularly for potentially explosive atmospheres:
- a single stirring zone, near to the container base, ensures easy mixing of settled residues, e.g. in flow-through mixing containers
- no baffles required, thus no additional sources of ignition
Customised shaft length possible. Fine polishing Ra 0.6 to 0.8 µm and/or material certificate available on request.
Properties
| Length mm: | 350 |
|---|---|
| Manufacturer Article Number: | 40 26446 00799 7 |
| Material No.: | 1.4404 |
| Type: | BuddeMix 1 |
| Ø agitator mm: | 60 |
| Ø agitator shaft mm: | 10 |
Skip product gallery
Compressed air powered stirrers, PLR, accessories
From
CHF 97.90*
Dissolver stirrers, stainless steel 1.4571
From
CHF 234.20*
Propeller, 3 blades, PTFE
From
CHF 195.00*
Anchor stirrer, PTFE
From
CHF 225.00*
Additional Stirrer Blades for Bola Stirrer Shafts, PTFE
From
CHF 91.90*
Dissolver stirring rotors, stainless steel 1.4404
From
CHF 294.70*
Rods for stirrer rotor shafts, M6, M8 and M10 screwthread end
From
CHF 8.00*
Paddle stirring rotors, stainless steel
From
CHF 226.00*
Turbine stirring rotors, 3-blade with guide ring, stainless steel 1.4305
From
CHF 254.20*
Stands
From
CHF 600.50*
Similar products
Connection couplings VK:Fixed-diameter connection for motor/magnetic coupling drive shaft and stirring rod. Suitable for use in potentially explosive atmospheres. Material No. 1.4404.Flexible glass stirring shaft couplings PK:For stirring tasks using glass stirring rods. Elastic connector between motor and stirring shaft. Provides exact alignment of motor and shaft, and evens out axial and height differences. Accepts 6mm to 10mm diameter shafts.Flexible glass stirring shaft couplings K:For stirring tasks using glass stirring rods. Elastic connector between motor and stirring shaft. Provides exact alignment of motor and shaft, and evens out axial and height differences. Accepts 6mm to 10mm diameter shaftsDouble-Cardan-Coupling DCK I:With 8mm dia. hexagonal input drive receiver and 6mm square socket drive output.
The dissolver stirrers create a radial flow with high turbulence. The mixture is drawn from top to bottom. High shear forces are created at the dissolver disk, which provides effective particle reduction. Recommended for medium to high speed operations.
The stirrer shafts consist of a PTFE-jacketed, stainless steel shaft and a stirrer paddle made of solid PTFE. The stainless steel core assures stability of the stirrer shaft and allows safe attachment of the stirrer chuck. Thanks to the thick PTFE coat and the paddle made of solid PTFE, the medium will only come into contact with PTFE. High chemical resistance makes it almost universally suitable. PTFE is extremely nonstick so that residues are repelled from shaft and paddle. The stirrer shafts are similar in size to (KPG) glass stirring rods and are therefore interchangeable easily.Operating temperature: -200°C to +250°CAdditional sizes and accessories are available on request.Information on the mixing effects of the different stirring geometries can be found in the descriptions of the stainless steel stirring rotors.The blades are inclined at 45 °. Recommended for medium to high speed operations.
The stirrer shafts consist of a PTFE-jacketed, stainless steel shaft and a stirrer paddle made of solid PTFE. The stainless steel core assures stability of the stirrer shaft and allows safe attachment of the stirrer chuck. Thanks to the thick PTFE coat and the paddle made of solid PTFE, the medium will only come into contact with PTFE. High chemical resistance makes it almost universally suitable. PTFE is extremely nonstick so that residues are repelled from shaft and paddle. The stirrer shafts are similar in size to (KPG) glass stirring rods and are therefore interchangeable easily.Operating temperature: -200°C to +250°CAdditional sizes and accessories are available on request.Information on the mixing effects of the different stirring geometries can be found in the descriptions of the stainless steel stirring rotors.Recommended for low speed operations.Additional wings available on request
Useful extension to the existing range of Bola stirrer shafts. The additional blades can optionally be fixed in your preferred position on every stirrer shaft with diameter 8,10 or 16 mm (a flat spanner is included). The stirrer blades are entirely made of PTFE, the mounting devices are made of a special PTFE-compound. A high chemical and thermical (-200 to +250 °C) resistance is assured. This "building block system" allows the user to define a stirrer of their own special requirements.
The dissolver stirring rotor creates a radial flow with high turbulence. The mixture is drawn from top to bottom. High shear forces are created at the dissolver disk, which provides effective particle reduction. Recommended for medium to high speed operations.
Stainless steel 1.4301. With screwthread fitting as outlined below.
The paddle stirring rotor creates a tangential flow with minimum turbulence. Its design ensures a gentle action on sensitive products and good heat exchange. Recommended for low to medium speed operations.Other sizes available on request.
The 3-blade turbine stirring rotor produces axial flow; the guide ring surrounding the blades reduces shear forces, and offers protection when contacting the wall or bottom of the vessel. Recommended for medium to high speed operations.
Floor stand BS 1 with angled foot, plastic-coated, stand rod Ø 34 x 1000 mmFloor stand BS 2 with angled foot, plastic-coated, stand rod Ø 34 x 1500 mmFloor stand BS 3 with angled foot 600 mm, completely made of stainless steel, stand rod Ø 34 x 1000 mmWall bracket WSRod diam. 34 x 1000 mm, clearance from wall: 200 mm.