High-temperature Tube Furnaces RHTH/RHTV series
CHF 31,676.50*
Content:
1
Delivery according to order confirmation
Product number:
9764565
Manufacturer:
Nabertherm GmbH
Packaging information:
Description
The high-temperature tube furnaces are available in either horizontal (type RHTH) or vertical (type RHTV) designs. High-quality insulation materials made of vacuum-formed fibre plates enable energy-saving operation and a fast heating time due to low heat storage and heat conductivity. By using different gas supply systems, operations can be performed under a protective gas atmosphere, vacuum, or even with flammable gasses.
Dimensions without tube.
Option:
- Tmax 1600 °C, 1700 °C or 1800 °C
- MoSi2 heating elements, mounted vertically for easy replacement
- Insulation with vacuum-formed ceramic fibre plates
- Rectangular outer housing with slots for convection cooling
- Models RHTV with hinges for wall mounting
- Housing made of sheets of textured stainless steel
- Ceramic working tube made of material C 799 incl. fibre plugs operation under air
- Type B thermocouple
- Switchgear separate from furnace in separate floor standing cabinet
- Switchgear with control unit
- Possible controller variants are the programmable B 500, C 550 and P 570 (threes) with adjustable ramps and hold times.
- Over-temperature limit controller with manual reset for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the oven and load
- Insulation only made of materials that are classified as not carcinogenic acc. to TRGS 905, class 1 or 2
- Standard power supply 400 V 3/N/PE 50/60 Hz
Dimensions without tube.
Option:
- Charge control with temperature measurement in the working tube and in the oven chamber behind the tube
- Alternative working tubes designed for process requirements
- Display of inner tube temperature with additional thermocouple
- Gas-tight flanges for protective gas and vacuum operation
- Manual or automatic gas supply system
- Three- or five-zone control for optimization of temperature uniformity
- Check valve at gas outlet avoids intrusion of false air
Properties
| Depth: | 650 mm |
|---|---|
| Dimensions (WxDxH): | 580 x 650 x 960 mm |
| Height: | 960 mm |
| Length tube: | 830 mm |
| Length tube heated: | 600 mm |
| Manufacturer Article Number: | RV322V62AN |
| Max. ext. tube Ø : | 120 mm |
| Max. temperature: | 1600 °C |
| Max. voltage: | 480 V |
| Min. voltage: | 380 V |
| Power supply: | 380 ... 480 V, 50/60 Hz |
| Power supply frequency: | 50/60 Hz |
| Rated capacity: | 19000 W |
| Type: | RHTV 120/600/16/P570 |
| Type of auxiliary energy: | Mains connection |
| Weight: | 110 kg |
| Width: | 580 mm |
Skip product gallery
Muffle furnaces SNOL 6.7/1300, up to 1300 °C, Omron E5CC controller
From
CHF 2,943.00*
Muffle Furnaces Series LE 1/11 - LE 24/11 up to 1100 °C
From
CHF 1,891.00*
Muffle furnaces Thermolyne™
From
CHF 1,803.00*
Muffle furnaces series LT, max. 1100 °C, with lift door
From
CHF 4,278.00*
Muffle furnaces series L, max. 1100 °C, with flap door
From
CHF 3,911.00*
High-temperature chamber furnaces with air circulation NA / NAT
From
CHF 13,493.00*
Muffle furnaces series LT, max. 1200 °C, with lift door
From
CHF 5,188.00*
Muffle furnaces series L, max. 1400 °C, with flap door
From
CHF 9,265.00*
Similar products
Muffle furnaces with fibre-insulated chambers and ceramic heating plates. Suitable for thermal treatments in industry, science and medicine.Side, top or down-opening door depending on modelOuter casing made of powder-coated sheet metalCeramic bottom plateControl panel in the lower part of the ovenIncl. door safety switchFast heating timeGood stability and temperature distributionLow power consumptionWith basic temperature controller Omron E5CC with adjustable temperature and time (not programmable)
Compact muffle furnaces with dual shell furnace housing of rust-free stainless steel and heating elements encased in quartz glass tubes.Tmax 1100 °C, working temperature 1050 °CHeating from two sides from heating elements in quartz glass tubesMaintenance-friendly replacement of heating elements and insulationInsulation only made of materials that are classified as not carcinogenic acc. to TRGS 905, class 1 or 2Housing made of sheets of textured stainless steelDual shell housing for low external temperatures and high stabilityFlap door which can also be used as a work platformExhaust air outlet in rear wallCompact dimensions and light weightController mounted under the door to save spaceEquipped with the basic controller R 7 with one free storeable temperature, which is dwelled until the controller is switch offStandard power supply 230 V, 1/N/PE, 50/60 HzExternal dimensions vary for versions with additional equipment. Dimensions on request.
The muffle furnaces are suitable for ashing, annealing processes, digestion, heat treatment of metals and drying processes at high temperatures.Built-in ventilation portDoor safety switch: when the door is opened, the power supply to the heating elements is interruptedPort in the rear of the chamber for external temperature monitoring
For daily laboratory use. Models with flap door or lift door available, for temperatures from 1100 °C to 1400 °C. Equipped with programmable controllers B 510 (with touch panel, 5 programmes with 4 segments each), or C 550 (with touch panel, 10 programmes with 20 segments each), L 1/12 with controller R 7 (continuous operation).Dual shell housing made of textured stainless steel sheets for low external temperatures and high stabilityAdjustable air inlet integrated in doorExhaust air outlet in rear wall of furnaceSolid state relays provide low-noise operationStandard connector 230 V 1/N/PE 50/60 Hz24 and 40 l with 400 V 3/N/PE 50/60 HzOptional:Chimney, chimney with fan or catalytic converterOver-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and loadProtective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)Manual or automatic gas supply systemProcess control and documentation via VCD software package for monitoring, documentation and controlCeramic heating plates with integrated heating wire, splash and exhaust protected, easy to replaceHeating from two sides (three sides for interior volumes of 24, 40 and 60 l)The hot side of the lift door is facing away from the operatorExternal dimensions vary for versions with additional equipment. Dimensions on request.
For daily laboratory use. Models with flap door or lift door available, for temperatures from 1100 °C to 1400 °C. Equipped with programmable controllers B 510 (with touch panel, 5 programmes with 4 segments each), or C 550 (with touch panel, 10 programmes with 20 segments each), L 1/12 with controller R 7 (continuous operation).Dual shell housing made of textured stainless steel sheets for low external temperatures and high stabilityAdjustable air inlet integrated in doorExhaust air outlet in rear wall of furnaceSolid state relays provide low-noise operationStandard connector 230 V 1/N/PE 50/60 Hz24 and 40 l with 400 V 3/N/PE 50/60 HzOptional:Chimney, chimney with fan or catalytic converterOver-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and loadProtective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)Manual or automatic gas supply systemProcess control and documentation via VCD software package for monitoring, documentation and controlCeramic heating plates with integrated heating wire, splash and exhaust protected, easy to replaceHeating from two sides (three sides for interior volumes of 24 and 40 l)Flap door can be used as work platformExternal dimensions vary for versions with additional equipment. Dimensions on request.
These chamber furnaces with air circulation are characterized by their extremely high temperature uniformity. Hence, they are especially suitable for processes such as cooling, crystalizing, preheating, curing, but also for numerous processes in tool making. Due to the modular concept, the forced convection furnaces can be adjusted to the process requirements by adding suitable equipment.Tmax 450 °C, 650 °C, or 850 °CHorizontal air circulationSwing door hinged on the rightTemperature uniformity up to ±4 °C according to DIN 17052-1 (model NA 15/65 and NAT 30/85 up to ±5 °C)Optimum air flow and temperature uniformity through high circulation ratesOne frame sheet and rails for two additional trays included in the scope of delivery (NA 15/65 and NAT 30/85 without frame sheet)Stainless steel air-baffles in the furnace for optimum air circulationBase frame included in the delivery, NA 15/65 and NAT 30/85 designed as table-top modelAir inlet and exhaust air flaps as additional equipment for using as drying ovenNTLog Basic for Nabertherm controller: recording of process data with USB-flash driveAvailable with the programmable controllers B 500 and C 540 with adjustable ramps and hold times (NA 15/65 with B 510 or C 550)Standard power supply 400 V 3/N/PE 50/60 Hz (NA 15/65: 220 - 240 V, 1/N/PE)External dimensions vary for versions with additional equipment. Dimensions on request.
For daily laboratory use. Models with flap door or lift door available, for temperatures from 1100 °C to 1400 °C. Equipped with programmable controllers B 510 (with touch panel, 5 programmes with 4 segments each), or C 550 (with touch panel, 10 programmes with 20 segments each), L 1/12 with controller R 7 (continuous operation).Dual shell housing made of textured stainless steel sheets for low external temperatures and high stabilityAdjustable air inlet integrated in doorExhaust air outlet in rear wall of furnaceSolid state relays provide low-noise operationStandard connector 230 V 1/N/PE 50/60 Hz24 and 40 l with 400 V 3/N/PE 50/60 HzOptional:Chimney, chimney with fan or catalytic converterOver-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and loadProtective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)Manual or automatic gas supply systemProcess control and documentation via VCD software package for monitoring, documentation and controlCeramic heating plates with integrated heating wire, splash and exhaust protected, easy to replaceHeating from two sides (three sides for interior volumes of 24, 40 and 60 l)Lift door with hot surface facing away from the operatorExternal dimensions vary for versions with additional equipment. Dimensions on request.
For daily laboratory use. Models with flap door or lift door available, for temperatures from 1100 °C to 1400 °C. Equipped with programmable controllers B 510 (with touch panel, 5 programmes with 4 segments each), or C 550 (with touch panel, 10 programmes with 20 segments each), L 1/12 with controller R 7 (continuous operation).Dual shell housing made of textured stainless steel sheets for low external temperatures and high stabilityAdjustable air inlet integrated in doorExhaust air outlet in rear wall of furnaceSolid state relays provide low-noise operationStandard connector 230 V 1/N/PE 50/60 Hz24 and 40 l with 400 V 3/N/PE 50/60 HzOptional:Chimney, chimney with fan or catalytic converterOver-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and loadProtective gas connection to purge with non-flammable protective or reaction gases (not available in combination with chimney, chimney with fan or catalytic converter)Manual or automatic gas supply systemProcess control and documentation via VCD software package for monitoring, documentation and controlMax. temperature 1400 °C (recommended working temperature for processes with longer dwell times is 1300 °C)Heating elements on support tubes for free heat radiation, short heating times and long service lifeHeating from two sidesFlap door can be used as work platformExternal dimensions vary for versions with additional equipment. Dimensions on request.